How to knot the red rope pendant: 1. Bake the rope with fire, pinch the wire while it is hot, so that the rope can pass through the hole, pay attention to the burns carefully. 2, the end of the rope passes through the pendant hole. 3, leaving ropes that are suitable for length to be tied to your personal habits, leaving 1cm here. 4. Open one end of the rope and go around the other side. 5, go around the other side to fight. 6. Repeat this again and again. 7.
Preparation tools: lane rope, scissors, lighter. 1. First of all, the fire roasting red rope can make it pass through the hole, as shown in the figure below: 2, the tie rope passes through the pendant hole together, as shown in the figure below: 3, leave a reasonable reasonable one The length is used to compile the rope, as shown in the figure below: 4, and then pass the two ropes from the back and make a simple cross section. 5, then go to the other side to hit a knot. Show: 7, and then gently bake the line heads left on the two sides with a lighter, as shown in the figure below: 8, the pendant rope is completed, as shown in the figure below: r r
Pay content for time limit to check for freenAnswer Hello, I am glad to answer it for you. The necklace pendant red rope can hit three ears, first put up three ears, turn the two lines below, press the right ear, repeat this step counterclockwise, and put the left ear into the gap in the two lines below to tighten. You can also hit the King Kong knot. After folding the line, press the left line on the right line, and then leave the left line from the right line to leave a circle, and then repeat this action to tighten. The necklace pendant red rope can hit the double -line knot, pass through the pendant through the rope, and pull the two ropes on the right side to the left two ropes to tighten it, and tie a dead knot. Drop the extra rope and burn it with a lighter.
Preparation tools: lane rope, scissors, lighter. 1, the fire roasting red rope, pumping the wire while it is hot, it can make it pass through the hole. 2, tie the rope fold and pass through the two ropes passing through the middle part through the pendant hole. 3. According to the size of the jade pendant, a reasonable length is used to compile and tie rope. Usually 0.5cm-2cm is more appropriate, leaving the length of the appropriate length as 1cm as a partial length. 4, then cross the two ropes from the back and make a simple cross section. 5, go around the other side to hit a knot. 6. Then, according to the thickness of the thickness of the line, the remaining line length is fixed with fire, and the threads on both sides are cut as shown in the figure below with scissors. 7, then gently bake the thread left on both sides with the lighter and quickly solidify. If the fire is too high, it may leave black spots. 8, complete.
n00:00 / 00: 5470% shortcut keys to describe space: Play / pause ESC: Exit full screen ↑: increase volume 10% ↓: decreases by 10% →: Single fast forward 5 seconds studio Here you can drag no longer appear in the player settings to reopen the small window shortcut key description
How to knot the red rope pendant:
1. Bake the rope with fire, pinch the wire while it is hot, so that the rope can pass through the hole, pay attention to the burns carefully.
2, the end of the rope passes through the pendant hole.
3, leaving ropes that are suitable for length to be tied to your personal habits, leaving 1cm here.
4. Open one end of the rope and go around the other side.
5, go around the other side to fight.
6. Repeat this again and again.
7.
Preparation tools: lane rope, scissors, lighter.
1. First of all, the fire roasting red rope can make it pass through the hole, as shown in the figure below:
2, the tie rope passes through the pendant hole together, as shown in the figure below:
3, leave a reasonable reasonable one The length is used to compile the rope, as shown in the figure below:
4, and then pass the two ropes from the back and make a simple cross section.
5, then go to the other side to hit a knot. Show:
7, and then gently bake the line heads left on the two sides with a lighter, as shown in the figure below:
8, the pendant rope is completed, as shown in the figure below: r r
Pay content for time limit to check for freenAnswer Hello, I am glad to answer it for you. The necklace pendant red rope can hit three ears, first put up three ears, turn the two lines below, press the right ear, repeat this step counterclockwise, and put the left ear into the gap in the two lines below to tighten. You can also hit the King Kong knot. After folding the line, press the left line on the right line, and then leave the left line from the right line to leave a circle, and then repeat this action to tighten. The necklace pendant red rope can hit the double -line knot, pass through the pendant through the rope, and pull the two ropes on the right side to the left two ropes to tighten it, and tie a dead knot. Drop the extra rope and burn it with a lighter.
Preparation tools: lane rope, scissors, lighter.
1, the fire roasting red rope, pumping the wire while it is hot, it can make it pass through the hole.
2, tie the rope fold and pass through the two ropes passing through the middle part through the pendant hole.
3. According to the size of the jade pendant, a reasonable length is used to compile and tie rope. Usually 0.5cm-2cm is more appropriate, leaving the length of the appropriate length as 1cm as a partial length.
4, then cross the two ropes from the back and make a simple cross section.
5, go around the other side to hit a knot.
6. Then, according to the thickness of the thickness of the line, the remaining line length is fixed with fire, and the threads on both sides are cut as shown in the figure below with scissors.
7, then gently bake the thread left on both sides with the lighter and quickly solidify. If the fire is too high, it may leave black spots.
8, complete.
Method of tie tutorial pendant rope
n00:00 / 00: 5470% shortcut keys to describe space: Play / pause ESC: Exit full screen ↑: increase volume 10% ↓: decreases by 10% →: Single fast forward 5 seconds studio Here you can drag no longer appear in the player settings to reopen the small window shortcut key description